The test specimen is hold between two round shaped grips. The grips are lined with rubber gasket to avoid the leakage of air through the edge. The two grips can be held the test specimen with the help of a hand spirited can mechanism.
The vacuum needed to draw the air through the test specimen is created with the vacuum pump supplied with the instrument. The vacuum pressure is measured by the manometer tube terms of mm of water level & airflow is measured by the rotameters supplied with the instrument.
The equipment is Metallic Dark Green paint & power coated finish for corrosion resistant finishing.
The Sky Touch Engineering Products Air Permeability tester for textiles is used for air permeability testing of the fabrics. Digital and analogue models are available. This system consists of an arrangement for holding the test specimens between two flat faces so as to expose a known area to the flow of air through it, a vacuum system to draw air through the exposed area of the test specimens. There is an arrangement to measure the volume of air flowing through the test specimen, and arrangement to measure the pressure drop between the faces of the test specimen. The test specimen is hold between two round-shaped grips. The grips are lined with rubber gasket to avoid the leakage of air through the edges. The two grips can be held the test specimens with the help of a hand operated screw mechanism. The vacuum needed to draw the air through the test specimens is created with the vacuum pump supplied with the instrument. The vacuum pressure is measured by the digital manometer (or manometer tube) in terms of mm of water level & airflow is measured by the Rotameters attached with the instrument. The equipment is metallic paint & bright chrome plating finish for corrosion resistant finishing.
Sky Touch Engineering Products Atmospheric Pressure Beaker Dyeing Machine is used for high temperature dying of fabric and yarn. This machine is used for sample dyeing of Yarn / fabrics at a max temperature of 98° C. The machine is model. Models are available on request.
The equipment is basically a doubled walled stainless steel tank. The inside/ outside tank are of SS 304 Grade sheet & jars are of SS 304 Grade. A motor & a cam – assembly are provided to give to & fro movement to SS rods to which yarn or fabric samples are tied.
Fabric Pilling Tester supplied with template, 8 rubber tubes and jig/fixture. Two box and four box models are available. The “Skytouch Engineering” Pilling Tester consists of two cubical boxers inner walls of box are lined by 3mm thick cork sheet. The boxes are rotate by means of motor about the horizontal axis. A pre-set digital counter is provided for stopping the tester after pre-determined number of revolutions. A template, metal cylinder, comprising Jig and 8-rubber tuber are provided with the instrument. Instrument is finished by bright chromes plating & metallic painting for corrosion resistant finish.
With our in-house facilities and decade of industrial experience, we are able to manufacture and supply a foremost range of Beasley Balance. These instruments are widely used in textile industries to evaluate the yarn count. Our Beasley Balance is designed and manufactured by our professionals as per the set industry norms using supreme grade materials. In addition, we offer these instruments in qualitative packaging to avoid damage during transportation.
the latest model direct yarn count balance to evaluate yarn count in
direct system. This specially designed equipment consists of a lightweight beam pivoted on Jewel Bearings
With a suspender hook at one end and a pointer at the other. The beam is initially leveled with the help of the
Leveling Screw to bring the pointer against a Datum Point.
A (Calibrated Rider) is suspended in the slot provided on the beam. A template is used to size the lengths of the
Yarn. (The Length depending upon the count system required). These sort lengths required to balance the
Beam gives the count of the yarn DIRECTLY.
We are a prominent Manufacturer, Exporter & Supplier of Color Matching Cabinet. The Color Matching Cabinet is used for visual inspection of any colored material like textile, paper, paint, ink, automotive etc. Standard Light sources are used for accurate testing and inspection. The Cabinet is completely made of MS Sheet with interior paint matching with Mussel N7 neutral gray paint and exterior powder coating with metallic finish.
Technical Specifications :
Conditioning Chamber offered comprise Lab Conditioner that comes in double walled structure which is filled with glass wool insulation. Here, the system features inner chamber made of stainless steel with outside body made of mild steel in powder coated finish. Further, our expertise also lies in making available fully SS models that feature two adjustable perforated shelves for keeping samples as well as chambers heated with air circulating fan with heater. Further, these also feature transparent viewing window to see the samples.
TexcareTMConditioning Chamber (Lab Conditioner)
Double walled structure filled with glass wool insulation.
Inner Chamber made of Stainless Steel and outside body is made of mild steel powder coated.
Fully SS models are also available.
Two adjustable perforated shelves for keeping the samples.
The chamber is heated with air circulating fan with heater.
The chamber is cooled electrically with the help of compressor cooling coils placed in ribs on the side of chamber.
Temperature controlled by Digital Temperature Indicator and Controller.
Humidity controlled by digital humidity controller.
Transparent viewing window to see the samples.
Light arrangement inside chamber to see the samples.
Push type door locking system.
Power 220 Volt AC 50 Hz. Single Phase
The Sky Touch Engineering Products Crease Recovery Tester is designed to measure crease recovery angle of fabrics. It consists of a rotary circular scale on which a spring type specimen clamp is fixed on the base plate on which the above arrangement is mounted. The test specimen is fixed on a loading strip supplied with the equipment. After folding the specimen on the creasing line marked on the strip, the loading strip with folded specimen is kept on an anvil under the dead load of the loading arrangement for a specified time. After that the specimen with the loading strip is transferred to the clamp of the rotary circular scale, where it is held in manner that the fold lies in a horizontal line on the axis of the circular scale. The circular scale with the clamp is rotated till the free limb of the specimen becomes vertical which is judged by aligning it to a vertical pointer. The crease recovery angle is directly read on the circular scale.
We bring forth a wide variety of quality assured Launder-O-Meter (Washing Fastness Tester) to our esteemed patrons. We have manufactured this range using optimum quality raw material. Customers can easily avail this range in various customized options as per their needs and demands. It is used in various industrial processes in various fields and sectors.
Our provided Martindale Abrasion cum Pilling Tester finds its main application in determining the abrasion and pilling resistance of various kinds of textiles. Fitted with touch screen support and 8 pegs, this tester is facilitated to accommodate many samples at the same time. It is supported with acrylic top plate for safety and loading station. Besides, all the components and control systems are checked stringently in order to ensure continuous running without any vibration. In this Martindale Abrasion cum Pilling Tester, central axis is rotated at a specified speed with the aid of a geared motor.
Technical Specification: Martindale Abrasion Cum Pilling Tester
Snap Pull Out Tester is used to determine the holding or breaking strength of prong-ring attached snap fasteners on the garments. The testing equipment comprises of an upper Snap-Clamp, a Lower Fabric Clamp & a Force Gauge mounted on a stand. The component to be tested is gripped by the Upper Snap Clamp and the garment is fixed to the Lower Fabric Clamp. Top fly wheel is turned with a specific force. The recording instrument displays the holding strength or the breaking strength of the snap component attached.
Our snap pull out tester are also used in paper industry for Elmendorf Tearing Strength. This test determines the average force required to propagate a single-rip tongue-type tear starting from a cut in paper, cardboard, plastics, non-woven and woven fabrics, with proper configuration.
We are able to achieve a position of repute in the industry by manufacturing and exporting a reliable range of Tearing Strength Testing Instruments. These instruments are extensively used in garment, leather and plastic industries for testing the tear strength of fabrics and plastic films. Precisely designed at our state of the art machining facility, our Tearing Strength Testing Instruments are made using quality materials procured from authentic vendors of the market. We lay prime emphasis on the packaging of these instruments to ensure safe delivery at clientsâ€™ end.
The Tearing Strength of Fabrics, Plastic Films or other similar material is determined by measurement of the work done in tearing through a fixed length of the test specimen using the Labin Tearing Strength Tester.
The Tearing Strength Testing Instruments of a Sector Pendulum Pivoted on anti-friction ball bearings on a vertical bracket fixed on a rigid metallic base. The test specimen in shape of a rectangular piece is held between two clamps, one of which is mounted on the pendulum and the other is mounted on the fixed bracket. The clamps are mounted in such a manner that their holding faces are aligned with each other when the pendulum is locked in its raised position.
The adjustable knife is also mounted on the bracket, on which the pendulum and the fixed clamp are mounted, it is centered between the two clamps for making initial slit in the test specimen. The pendulum is released by lifting a release lever. This action causes the test specimen to tear right through. The Tearing Strength is indicated on a scale fitted on the pendulum against a low friction pointer pivoted on the axis of the pendulum.
A set of CHECK WEIGHTS is supplied with the tester for verification of the Scale.
In order to increase the capacity of the Tester, augmenting weights are supplied as STANDARD ACCESSORIES For testing of low strength materials, multiple specimens may be mounted at the same time.